| 601 |
The port handle is invalid. |
| 602 |
The port is already open. |
| 603 |
Caller's buffer is too small. |
| 604 |
Wrong information specified. |
| 605 |
Cannot set port information. |
| 606 |
The port is not connected. |
| 607 |
The event is invalid. |
| 608 |
The device does not exist. |
| 609 |
The device type does not exist. |
| 610 |
The buffer is invalid. |
| 611 |
The route is not available. |
| 612 |
The route is not allocated. |
| 613 |
Invalid compression specified. |
| 614 |
Out of buffers. |
| 615 |
The port was not found. |
| 616 |
An asynchronous request is pending. |
| 617 |
The port or device is already disconnecting. |
| 618 |
The port is not open. |
| 619 |
The port is disconnected. |
| 620 |
There are no endpoints. |
| 621 |
Cannot open the phone book file. |
| 622 |
Cannot load the phone book file. |
| 623 |
Cannot find the phone book entry. |
| 624 |
Cannot write the phone book file. |
| 625 |
Invalid information found in the phone book. |
| 626 |
Cannot load a string. |
| 627 |
Cannot find key. |
| 628 |
The port was disconnected. |
| 629 |
The port was disconnected by the remote machine. |
| 630 |
The port was disconnected due to hardware failure. |
| 631 |
The port was disconnected by the user. |
| 632 |
The structure size is incorrect. |
| 633 |
The port is already in use or is not configured for
Remote Access dialout. |
| 634 |
Cannot register your computer on the remote network. |
| 635 |
Unknown error. |
| 636 |
The wrong device is attached to the port. |
| 637 |
The string could not be converted. |
| 638 |
The request has timed out. |
| 639 |
No asynchronous net available. |
| 640 |
A NetBIOS error has occurred. |
| 641 |
The server cannot allocate NetBIOS resources needed to
support the client. |
| 642 |
One of your NetBIOS names is already registered on the
remote network. |
| 643 |
A network adapter at the server failed. |
| 644 |
You will not receive network message popups. |
| 645 |
Internal authentication error. |
| 646 |
The account is not permitted to log on at this time of
day. |
| 647 |
The account is disabled. |
| 648 |
The password has expired. |
| 649 |
The account does not have Remote Access permission. |
| 650 |
The Remote Access server is not responding. |
| 651 |
Your modem (or other connecting device) has reported an
error. |
| 652 |
Unrecognized response from the device. |
| 653 |
A macro required by the device was not found in the
device .INF file section. |
| 654 |
A command or response in the device .INF file section
refers to an undefined macro |
| 655 |
The <message> macro was not found in the device .INF file
section. |
| 656 |
The <defaultoff> macro in the device .INF file section
contains an undefined macro |
| 657 |
The device .INF file could not be opened. |
| 658 |
The device name in the device .INF or media .INI file is
too long. |
| 659 |
The media .INI file refers to an unknown device name. |
| 660 |
The device .INF file contains no responses for the
command. |
| 661 |
The device .INF file is missing a command. |
| 662 |
Attempted to set a macro not listed in device .INF file
section. |
| 663 |
The media .INI file refers to an unknown device type. |
| 664 |
Cannot allocate memory. |
| 665 |
The port is not configured for Remote Access. |
| 666 |
Your modem (or other connecting device) is not
functioning. |
| 667 |
Cannot read the media .INI file. |
| 668 |
The connection dropped. |
| 669 |
The usage parameter in the media .INI file is invalid. |
| 670 |
Cannot read the section name from the media .INI file. |
| 671 |
Cannot read the device type from the media .INI file. |
| 672 |
Cannot read the device name from the media .INI file. |
| 673 |
Cannot read the usage from the media .INI file. |
| 674 |
Cannot read the maximum connection BPS rate from the
media .INI file. |
| 675 |
Cannot read the maximum carrier BPS rate from the media
.INI file. |
| 676 |
The line is busy. |
| 677 |
A person answered instead of a modem. |
| 678 |
There is no answer. |
| 679 |
Cannot detect carrier. |
| 680 |
There is no dial tone. |
| 681 |
General error reported by device. |
| 682 |
ERROR WRITING SECTIONNAME |
| 683 |
ERROR WRITING DEVICETYPE |
| 684 |
ERROR WRITING DEVICENAME |
| 685 |
ERROR WRITING MAXCONNECTBPS |
| 686 |
ERROR WRITING MAXCARRIERBPS |
| 687 |
ERROR WRITING USAGE |
| 688 |
ERROR WRITING DEFAULTOFF |
| 689 |
ERROR READING DEFAULTOFF |
| 690 |
ERROR EMPTY INI FILE |
| 691 |
Access denied because username and/or password is invalid
on the domain. |
| 692 |
Hardware failure in port or attached device. |
| 693 |
ERROR NOT BINARY MACRO |
| 694 |
ERROR DCB NOT FOUND |
| 695 |
ERROR STATE MACHINES NOT STARTED |
| 696 |
ERROR STATE MACHINES ALREADY STARTED |
| 697 |
ERROR PARTIAL RESPONSE LOOPING |
| 698 |
A response keyname in the device .INF file is not in the
expected format. |
| 699 |
The device response caused buffer overflow. |
| 700 |
The expanded command in the device .INF file is too long. |
| 701 |
The device moved to a BPS rate not supported by the COM
driver. |
| 702 |
Device response received when none expected. |
| 703 |
ERROR INTERACTIVE MODE |
| 704 |
ERROR BAD CALLBACK NUMBER |
| 705 |
ERROR INVALID AUTH STATE |
| 706 |
ERROR WRITING INITBPS |
| 707 |
X.25 diagnostic indication. |
| 708 |
The account has expired. |
| 709 |
Error changing password on domain. |
| 710 |
Serial overrun errors were detected while communicating
with your modem. |
| 711 |
RasMan initialization failure. Check the event log. |
| 712 |
Biplex port is initializing. Wait a few seconds and
redial. |
| 713 |
No active ISDN lines are available. |
| 714 |
Not enough ISDN channels are available to make the call. |
| 715 |
Too many errors occurred because of poor phone line
quality. |
| 716 |
The Remote Access IP configuration is unusable. |
| 717 |
No IP addresses are available in the static pool of
Remote Access IP addresses. |
| 718 |
PPP timeout. |
| 719 |
PPP terminated by remote machine. |
| 720 |
No PPP control protocols configured. |
| 721 |
Remote PPP peer is not responding. |
| 722 |
The PPP packet is invalid. |
| 723 |
The phone number, including prefix and suffix, is too
long. |
| 724 |
The IPX protocol cannot dial-out on the port because the
computer is an IPX router. |
| 725 |
The IPX protocol cannot dial-in on the port because the
IPX router is not installed. |
| 726 |
The IPX protocol cannot be used for dial-out on more than
one port at a time. |
| 727 |
Cannot access TCPCFG.DLL. |
| 728 |
Cannot find an IP adapter bound to Remote Access. |
| 729 |
SLIP cannot be used unless the IP protocol is installed.
|
| 730 |
Computer registration is not complete. |
| 731 |
The protocol is not configured. |
| 732 |
The PPP negotiation is not converging. |
| 733 |
The PPP control protocol for this network protocol is not
available on the server. |
| 734 |
The PPP link control protocol terminated.. |
| 735 |
The requested address was rejected by the server.. |
| 736 |
The remote computer terminated the control protocol. |
| 737 |
Loopback detected.. |
| 738 |
The server did not assign an address. |
| 739 |
The remote server cannot use the Windows NT encrypted
password. |
| 740 |
The TAPI devices configured for Remote Access failed to
initialize or were not installed correctly. |
| 741 |
The local computer does not support encryption. |
| 742 |
The remote server does not support encryption. |
| 743 |
The remote server requires encryption. |
| 744 |
Cannot use the IPX net number assigned by the remote
server. Check the event log. |
| 745 |
ERROR_INVALID_SMM |
| 746 |
ERROR_SMM_UNINITIALIZED |
| 747 |
ERROR_NO_MAC_FOR_PORT |
| 748 |
ERROR_SMM_TIMEOUT |
| 749 |
ERROR_BAD_PHONE_NUMBER |
| 750 |
ERROR_WRONG_MODULE |
| 751 |
The callback number contains an invalid character. Only
the following 18 characters are allowed: 0 to 9, T, P, W, (, ), -, @, and
space |
| 752 |
A syntax error was encountered while processing a script. |
| 753 |
The connection could not be disconnected because it was
created by the multi-protocol router. |
| 754 |
The system could not find the multi-link bundle. |
| 755 |
The system cannot perform automated dial because this
connection has a custom dialer specified. |
| 756 |
This connection is already being dialed. |
| 757 |
Remote Access Services could not be started automatically.
Additional information is provided in the event log. |
| 758 |
Internet Connection Sharing is already enabled on the
connection. |
| 759 |
An error occurred while the existing Internet Connection
Sharing settings were being changed. |
| 760 |
An error occurred while routing capabilities were being
enabled. |
| 761 |
An error occurred while Internet Connection Sharing was
being enabled for the connection. |
| 762 |
An error occurred while the local network was being
configured for sharing. |
| 763 |
Internet Connection Sharing cannot be enabled. There is
more than one LAN connection other than the connection to be shared.
|
| 764 |
No smart card reader is installed. |
| 765 |
Internet Connection Sharing cannot be enabled. A LAN
connection is already configured with the IP address that is required for
automatic IP addressing. |
| 766 |
A certificate could not be found. Connections that use
the L2TP protocol over IPSec require the installation of a machine
certificate, also known as a computer certificate. |
| 767 |
Internet Connection Sharing cannot be enabled. The LAN
connection selected as the private network has more than one IP address
configured. Please reconfigure the LAN connection with a single IP address
before enabling Internet Connection Sharing. |
| 768 |
The connection attempt failed because of failure to
encrypt data. |
| 769 |
The specified destination is not reachable. |
| 770 |
The remote computer rejected the connection attempt.
|
| 771 |
The connection attempt failed because the network is busy.
|
| 772 |
The remote computer's network hardware is incompatible
with the type of call requested. |
| 773 |
The connection attempt failed because the destination
number has changed. |
| 774 |
The connection attempt failed because of a temporary
failure. Try connecting again. |
| 775 |
The call was blocked by the remote computer. |
| 776 |
The call could not be connected because the remote
computer has invoked the Do Not Disturb feature. |
| 777 |
The connection attempt failed because the modem (or other
connecting device on the remote computer is out of order. |
| 778 |
It was not possible to verify the identity of the server.
|
| 779 |
To dial out using this connection you must use a smart
card. |
| 780 |
An attempted function is not valid for this connection.
|
| 781 |
The connection requires a certificate, and no valid
certificate was found. For further assistance, click More Info or search
Help and Support Center for this error number. |
| 782 |
Internet Connection Sharing (ICS and Internet Connection
Firewall (ICF cannot be enabled because Routing and Remote Access has been
enabled on this computer. To enable ICS or ICF, first disable Routing and
Remote Access. For more information about Routing and Remote Access, ICS, or
ICF, see Help and Support. |
| 783 |
Internet Connection Sharing cannot be enabled. The LAN
connection selected as the private network is either not present, or is
disconnected from the network. Please ensure that the LAN adapter is
connected before enabling Internet Connection Sharing. |
| 784 |
You cannot dial using this connection at logon time,
because it is configured to use a user name different than the one on the
smart card. If you want to use it at logon time, you must configure it to
use the user name on the smart card. |
| 785 |
You cannot dial using this connection at logon time,
because it is not configured to use a smart card. If you want to use it at
logon time, you must edit the properties of this connection so that it uses
a smart card. |
| 786 |
The L2TP connection attempt failed because there is no
valid machine certificate on your computer for security authentication.
|
| 787 |
The L2TP connection attempt failed because the security
layer could not authenticate the remote computer. |
| 788 |
The L2TP connection attempt failed because the security
layer could not negotiate compatible parameters with the remote computer.
|
| 789 |
The L2TP connection attempt failed because the security
layer encountered a processing error during initial negotiations with the
remote computer. |
| 790 |
The L2TP connection attempt failed because certificate
validation on the remote computer failed. |
| 791 |
The L2TP connection attempt failed because security
policy for the connection was not found. |
| 792 |
The L2TP connection attempt failed because security
negotiation timed out. |
| 793 |
The L2TP connection attempt failed because an error
occurred while negotiating security. |
| 794 |
The Framed Protocol RADIUS attribute for this user is not
PPP. |
| 795 |
The Tunnel Type RADIUS attribute for this user is not
correct. |
| 796 |
The Service Type RADIUS attribute for this user is
neither Framed nor Callback Framed. |
| 797 |
A connection to the remote computer could not be
established because the modem was not found or was busy. For further
assistance, click More Info or search Help and Support Center for this error
number. |
| 798 |
A certificate could not be found that can be used with
this Extensible Authentication Protocol. |
| 799 |
Internet Connection Sharing (ICS cannot be enabled due to
an IP address conflict on the network. ICS requires the host be configured
to use 192.168.0.1. Please ensure that no other client on the network is
configured to use 192.168.0.1. |
| 800 |
Unable to establish the VPN connection. The VPN server
may be unreachable, or security parameters may not be configured properly
for this connection. |
| 801 |
This connection is configured to validate the identity of
the access server, but Windows cannot verify the digital certificate sent by
the server. |
| 802 |
The card supplied was not recognized. Please check that
the card is inserted correctly, and fits tightly. |
| 803 |
The PEAP configuration stored in the session cookie does
not match the current session configuration. |
| 804 |
The PEAP identity stored in the session cookie does not
match the current identity. |
| 805 |
You cannot dial using this connection at logon time,
because it is configured to use logged on user's credentials. |
| 900 |
The router is not running. |
| 901 |
The interface is already connected. |
| 902 |
The specified protocol identifier is not known to the
router. |
| 903 |
The Demand-dial Interface Manager is not running.
|
| 904 |
An interface with this name is already registered with
the router. |
| 905 |
An interface with this name is not registered with the
router. |
| 906 |
The interface is not connected. |
| 907 |
The specified protocol is stopping. |
| 908 |
The interface is connected and hence cannot be deleted. |
| 909 |
The interface credentials have not been set. |
| 910 |
This interface is already in the process of connecting.
|
| 911 |
An update of routing information on this interface is
already in progress. |
| 912 |
The interface configuration in invalid. There is already
another interface that is connected to the same interface on the remote
router. |
| 913 |
A Remote Access Client attempted to connect over a port
that was reserved for Routers only. |
| 914 |
A Demand Dial Router attempted to connect over a port
that was reserved for Remote Access Clients only. |
| 915 |
The client interface with this name already exists and is
currently connected. |
| 916 |
The interface is in a disabled state. |
| 917 |
The authentication protocol was rejected by the remote
peer. |
| 918 |
There are no authentication protocols available for use.
|
| 919 |
The remote computer refused to be authenticated using the
configured authentication protocol. The line has been disconnected.
|
| 920 |
The remote account does not have Remote Access permission.
|
| 921 |
The remote account has expired. |
| 922 |
The remote account is disabled. |
| 923 |
The remote account is not permitted to logon at this time
of day. |
| 924 |
Access was denied to the remote peer because username
and/or password is invalid on the domain. |
| 925 |
There are no routing enabled ports available for use by
this demand dial interface. |
| 926 |
The port has been disconnected due to inactivity.
|
| 927 |
The interface is not reachable at this time. |
| 928 |
The Demand Dial service is in a paused state.
|
| 929 |
The interface has been disconnected by the administrator.
|
| 930 |
The authentication server did not respond to
authentication requests in a timely fashion. |
| 931 |
The maximum number of ports allowed for use in the
multilinked connection has been reached. |
| 932 |
The connection time limit for the user has been reached.
|
| 933 |
The maximum limit on the number of LAN interfaces
supported has been reached. |
| 934 |
The maximum limit on the number of Demand Dial interfaces
supported has been reached. |
| 935 |
The maximum limit on the number of Remote Access clients
supported has been reached. |
| 936 |
The port has been disconnected due to the BAP policy.
|
| 937 |
Because another connection of your type is in use, the
incoming connection cannot accept your connection request. |
| 938 |
No RADIUS servers were located on the network.
|
| 939 |
An invalid response was received from the RADIUS
authentication server. Make sure that the case sensitive secret password for
the RADIUS server is set correctly. |
| 940 |
You do not have permission to connect at this time.
|
| 941 |
You do not have permission to connect using the current
device type. |
| 942 |
You do not have permission to connect using the selected
authentication protocol. |
| 943 |
BAP is required for this user. |
| 944 |
The interface is not allowed to connect at this time.
|
| 945 |
The saved router configuration is incompatible with the
current router. |
| 946 |
RemoteAccess has detected older format user accounts that
will not be migrated automatically. To migrate these manually, run XXXX.
|
| 948 |
The transport is already installed with the router.
|
| 949 |
Received invalid signature length in packet from RADIUS
server. |
| 950 |
Received invalid signature in packet from RADIUS server.
|
| 951 |
Did not receive signature along with EAPMessage from
RADIUS server. |
| 952 |
Received packet with invalid length or Id from RADIUS
server. |
| 953 |
Received packet with attribute with invalid length from
RADIUS server. |
| 954 |
Received invalid packet from RADIUS server. |
| 955 |
Authenticator does not match in packet from RADIUS server. |
